Altivar Easy 610

Variable speed drive

Fan, pump, compressor, conveyor

ATV610

Standard version

Asynchronous motors

Cabinet mount

Integrated conforming to EN/IEC 61800-3 category C3 with 50 m maximum

IP20

Forced convection

50...60 Hz (+/-5 %)

3 phases

380...415 V (- 15...10 %)

45 kW normal duty
37 kW heavy duty

60 hp normal duty
50 hp heavy duty

92.9 A at 380 V normal duty
88.3 A at 415 V normal duty
80.5 A at 380 V heavy duty
75.8 A at 415 V heavy duty

22 kA

63.5 kVA at 415 V normal duty
54.5 kVA at 415 V heavy duty

88 A at 4 kHz normal duty
75 A at 4 kHz heavy duty

97 A during 60 s normal duty
112 A during 60 s heavy duty

Constant torque standard
Variable torque standard
Optimized torque mode

0.0001...0.5 kHz

4 kHz

2...12 kHz adjustable

16 preset speeds

Modbus serial

Slot A : communication card Profibus DP V1
Slot A : digital or analog I/O extension card
Slot A : relay output card

<= power supply voltage

Adjustable
Automatic whatever the load
Can be suppressed
Not available in permanent magnet motor law

Linear adjustable separately from 0.01 to 9000 s
S, U or customized

By DC injection

Motor : thermal protection
Motor : motor phase break
Drive : thermal protection
Drive : overheating
Drive : overcurrent between output phases and earth
Drive : overload of output voltage
Drive : short-circuit protection
Drive : motor phase break
Drive : overvoltages on the DC bus
Drive : line supply overvoltage
Drive : line supply undervoltage
Drive : line supply phase loss
Drive : overspeed
Drive : break on the control circuit

Display unit : 0.1 Hz
Analog input : 0.012/50 Hz

Line side, screw terminal : 35...50 mm²
Control, screw terminal : 0.5...1.5 mm²
Motor, screw terminal : 50 mm²

1 RJ45 (on the remote graphic terminal) for Modbus serial

2-wire RS 485 for Modbus serial

RTU for Modbus serial

4.8, 9.6, 19.2, 38.4 kbit/s for Modbus serial

No impedance for Modbus serial

1...247 for Modbus serial

Slave

External supply for digital inputs : 24 V DC (limits : 19...30 V), <= 1.25 mA (overload and short-circuit protection)
Internal supply for reference potentiometer (1 to 10 kOhm) : 10.5 V DC +/- 5 %, <= 10 mA (overload and short-circuit protection)

1 LED red for presence of voltage
2 LEDs for local diagnostic
1 LED yellow for embedded communication status
2 LEDs dual colour for communication module status

226 mm

613 mm
706 mm with EMC plate

271 mm

26.8 kg

3

Software-configurable voltage AI1, AI2, AI3 : 0...10 V DC, impedance 30 kOhm, resolution 12 bits
Software-configurable current AI1, AI2, AI3 : 0...20 mA, impedance 250 Ohm, resolution 12 bits
Software-configurable temperature probe or water level sensor AI2, AI3

6

Programmable as pulse input DI5, DI6 0...30 kHz : 24 V DC (limits : <= 30 V)
Programmable as logic input DI1...DI6 : 24 V DC (limits : <= 30 V), impedance 3.5 kOhm

Level 1 PLC conforming to EN/IEC 61131-2, logic input DI1...DI6
Level 1 PLC conforming to IEC 65A-68, pulse input DI5, DI6

Positive logic (source) : DI1...DI6 configurable logic input, < 5 V (state 0), > 11 V (state 1)
Negative logic (sink) : DI1...DI6 configurable logic input, > 16 V (state 0), < 10 V (state 1)
Positive logic (source) : DI5, DI6 configurable pulse input, < 0.6 V (state 0), > 2.5 V (state 1)

2

Software-configurable current AQ1, AQ2 : 0...20 mA, resolution 10 bits
Software-configurable voltage AQ1, AQ2 : 0...10 V DC,impedance 470 Ohm, resolution 10 bits

Analog input AI1, AI2, AI3 : 5 ms (+/- 0.1 ms)
Analog output AQ1, AQ2 : 10 ms (+/- 1 ms)
Discrete input DI1...DI6 : 2 ms (+/- 0.5 ms) configurable
Pulse input DI5, DI6 : 5 ms (+/- 1 ms) configurable

Analog input AI1, AI2, AI3 : +/- 0.6 % for a temperature variation 60 °C
Analog output AQ1, AQ2 : +/- 1 % for a temperature variation 60 °C

Analog input AI1, AI2, AI3 : +/- 0.15 % of maximum value
Analog output AQ1, AQ2 : +/- 0.2 %

3

Configurable relay logic R1 : fault relay NO/NC, electrical durability 100000 cycles
Configurable relay logic R2 : sequence relay NO, electrical durability 100000 cycles
Configurable relay logic R3 : sequence relay NO, electrical durability 100000 cycles

Relay output R1, R2, R3 : 5 ms (+/- 0.5 ms)

Relay output R1, R2, R3 : 5 mA at 24 V DC

Relay output R1, R2, R3 on resistive load (cos phi = 1 : 3 A at 250 V AC
Relay output R1, R2, R3 on resistive load (cos phi = 1 : 3 A at 30 V DC
Relay output R1, R2, R3 on inductive load (cos phi = 0.4 and L/R = 7 ms) : 2 A at 250 V AC
Relay output R1, R2, R3 on inductive load (cos phi = 0.4 and L/R = 7 ms) : 2 A at 30 V DC

Between power and control terminals

> 1 mOhm at 500 V DC for 1 minute to earth

75 dB conforming to 86/188/EEC

1000 W (forced convection) at 380 V, switching frequency 4 kHz
121 W (natural convection) at 380 V, switching frequency 4 kHz

240 m3/h

Vertical +/- 10 degree

1.2/50 µs - 8/20 µs surge immunity test level 3 conforming to IEC 61000-4-5
Electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-4
Electrostatic discharge immunity test level 3 conforming to IEC 61000-4-2
Radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3
Conducted radio-frequency immunity test level 3 conforming to IEC 61000-4-6

2 conforming to EN/IEC 61800-5-1

1.5 mm peak to peak (f= 2...13 Hz) conforming to IEC 60068-2-6
1 gn (f= 13...200 Hz) conforming to IEC 60068-2-6

15 gn during 11 ms conforming to IEC 60068-2-27

5...95 % without condensation conforming to IEC 60068-2-3

-15...45 °C without derating
45...60 °C with derating factor

-40...70 °C

1000...4800 m with current derating 1 % per 100 m
<= 1000 m without derating

Chemical pollution resistance class 3C3 conforming to EN/IEC 60721-3-3
Dust pollution resistance class 3S3 conforming to EN/IEC 60721-3-3

EN/IEC 61800-3
EN/IEC 61800-3 environment 2 category C3
EN/IEC 61800-5-1
IEC 60721-3

REACH

CE

Green Premium product